Why Do My Headphones Keep Disconnecting? Bluetooth gadgets are not faultless and have flaws of their own. Indeed, one common issue you may be experiencing is that your headset keeps disconnecting from your phone or tablet.
This can ruin the entire experience, especially if you can’t figure out what’s wrong.
Don’t be concerned! This Bluetooth headset issue has a simple solution, which you may read about in this post. I’ll answer all of the most frequently asked questions from users.
Low battery, device interference, being too far away from the source device, and a weak Bluetooth signal are a few of the causes of headphones that keep disconnecting. You can try restarting both devices, getting away from any potential interference sources, and making sure your Bluetooth headset is fully charged to see if that resolves the problem.
Quick Answer, Why do my Headphones Keep Disconnecting?
Why do my Headphones Keep Disconnecting?
One apparent advantage of wired headphones over Bluetooth headphones is that they do not detach. In fact, connected headphones ensure that the audio stream is transmitted without loss or interruption.
This dependability is due to the fact that the signal in wired headphones flows over a wire. As a result, there is no interference with the headphones. Bluetooth headphones, on the other hand, rely on radio waves delivered across the air to carry audio signals.
This technique has the advantage of eliminating the requirement for a physical connection or unsightly wires between your headphones and your device. However, one problem is that interference and other radio noise can cause Bluetooth headphones to lose connectivity.
Furthermore, your Bluetooth headset may continue to disconnect for various reasons. Some Bluetooth headphones do not work with all phones and devices. As a result, these Bluetooth headsets frequently disconnect or fail to connect!
Although Bluetooth headphones transmit signals across the air, their range is still limited. The greater the distance between the Bluetooth headset and your phone, the weaker the connection. When you go far enough away from the Bluetooth device, it will eventually disconnect.
This is due to the fact that the radio waves that connect your Bluetooth headphones and your device cannot reach vast distances. Most Bluetooth devices have a maximum range of 30 feet. As a result, you should keep your phone and Bluetooth headset no more than 30 feet apart.
4. There are too many background apps
We frequently leave dozens of apps open in the background of our phones. These apps not only slow down your phone, but they also have an impact on Bluetooth headphones and other devices that are connected to it.
When there are too many apps running in the background, Bluetooth headsets become confused. As a result, they interfere with the connection between the phone and the Bluetooth headphone.
You will eventually lose the connection between your phone and the headset as a result of this. Fortunately, this is a simple issue to resolve; simply keep your apps organized and your background uncluttered!
5. Duplicates Contact
Many of us have duplicate contact information on our phones. Duplicate contacts are created while syncing accounts or switching phones and are often safe. However, having duplicate contacts on your phone can have a detrimental impact on Bluetooth connections.
Have you ever picked up a phone call while using your Bluetooth headset only to have the call dropped? If this is the case, having duplicate contacts on your phone is most likely the blame.
Multiple contacts with the same name or phone number can cause your Bluetooth headset to become confused. This is due to the Bluetooth headset’s inability to determine which of the contacts the call is linked to.
Although the procedure may be time-consuming, you should go through your contacts and erase any duplicates. You will have lowered the likelihood of a call disconnection by doing so.
How to Fix Headphones keep Disconnecting?
The first thing you should do is make sure your Bluetooth headphones and phone aren’t too far away. Although Bluetooth devices have a maximum range of 30 feet, you should not utilize them more than 3-4 feet apart.
Furthermore, the main Bluetooth antenna is always situated in your headphones’ inline remote. As a result, if your inline remote is on the right, keep your phone in your right hand or pocket. In contrast, if the inline remote is on the left side, keep your device on the left.
If you continue to have problems despite these adjustments, you should consider restarting your devices. First, turn off your Bluetooth headset. Try pairing it to your phone or device again after it has switched on. Often, this is sufficient to resolve the problem.
If restarting the Bluetooth headset does not resolve the problem, restart your phone as well and try connecting again.
3. Interference Reduction
Bluetooth signals, as previously said, move over the air. As a result, they are vulnerable to interference. WiFi routers are a common source of interference.
Wifi routers generate radio waves that are comparable to those emitted by Bluetooth devices. As a result, you can try shutting off your WiFi router or moving away from it. You can reduce interference by increasing the distance between your Bluetooth headset and the wifi router.
Furthermore, USB 3.0 ports can interfere with the Bluetooth headset and your phone. If your laptop or desktop computer has a USB 3.0 port, you should utilize your Bluetooth apple device away from the computer.
By completing these steps, you can reduce interference in the Bluetooth connection between your headphones and mobile phone. Less interference means a better connection between your Bluetooth earbuds and your phone. As a result, your gadgets will no longer disconnect as frequently.
How to Restore Disconnected Apple AirPods from an iPhone?
To prevent your AirPods or wireless headphone from losing Bluetooth connectivity, go through the list of likely causes and delete them one by one.
Have you inadvertently turned off the Bluetooth setting or selected the incorrect audio output? Is it a physical issue with one earbud, is ear detection malfunctioning, or do the AirPods simply need to be cleaned? Finally, we can look for potential causes of signal interference.
Step 1: Ensure that you have the appropriate software.
- iOS 15.1 or macOS 12 are required for the AirPods 3.
- AirPods Pro is compatible with iOS 13.2 and macOS 10.15.1 or later.
- The original AirPods 2 require iOS 12.2 or macOS 10.14.
Step 2: Inspect the battery levels.
The first step is to ensure that your AirPods are fully charged. You won’t be able to hear anything if they’re out of power.
Follow these steps to check the charge status of your AirPods on your iPhone:
- Open the lid and place the case next to your iPhone with the AirPods inside.
- The battery levels will be displayed in a popup on your iPhone.
- You may also use your iPhone’s Batteries widget to check the status of your batteries. Scroll down by swiping from left to right on the Home page.
- If you haven’t already done so, scroll down until you see Edit, tap on it, and then add Batteries.
- This widget will also display the battery status of any other Apple devices that are linked to it, such as an Apple Watch.
- In addition, here’s how to extend the life of your AirPods’ battery.
Step 3: Verify Bluetooth
- Check that Bluetooth is turned on on the device with which you’re using the AirPods.
- Open Control Centre on your iPhone or iPad and make sure Bluetooth is turned on.
- Alternately, go to Bluetooth > Settings. A green indicator should appear to indicate that Bluetooth is turned on. Even if Bluetooth is turned on, it is worthwhile to turn it off and on again.
- Tap the green switch in Settings > Bluetooth until it becomes white.
- Wait at least 15 seconds before reactivating Bluetooth.
- It will now say that your AirPods are not linked, but they should reconnect as soon as you select them as the audio source (see the next step).
Step 4: Examine your audio device’s settings
- Make sure you’ve selected your AirPods as the output audio device – this may happen automatically because the AirPods detect that they’re in your ears, but if it hasn’t, follow these instructions.
- While listening to music on your iPhone Tap the AirPlay icon that appears beneath the track (if you have the track selected).
- Choose your AirPods from the available options.
- If you’re on a call, make sure you’ve picked AirPods from the audio options that display on the screen when you initiate the call.
- When you’re on a call, you may also change the audio source by pressing the speaker icon.
Step 5: Disconnect and then rejoin your AirPods
- “Turning it off and on again” can address a variety of problems with electronic gadgets, including the AirPods.
- Close the lid on the AirPods case and wait about 15 seconds.
- Open the lid and press and hold the setup button on the case’s back.
- Wait for the light to flash amber, followed by white.
- Your AirPods have now been reset (even if they aren’t your AirPods).
- Simply place your AirPods next to your iPhone to reconnect them (make sure you have Bluetooth turned on).
- Now go through the iPhone’s setup choices.
Step 6: Resetting your AirPods
If the previous steps were ineffective, try resetting the AirPods. To accomplish this, take these steps:
- Close the charging case and place the AirPods inside.
- Wait thirty seconds before reopening the cover.
- Navigate to the Bluetooth settings on your iPad or iPhone and look for your AirPods in the device list. A little I sign appears next to the devices. When you click on this button, a new page will open.
- Select “Ignore this device.”
- Let’s go back to the charging case: Keep the lid open for 15 seconds and hit the setup button on the rear. After that, the display should flash amber and then white.
Step 7: Wipe down your AirPods
Because it’s conceivable that your issue is due to filth, you should clean them.
This is a sensitive technique because you don’t want to scratch, blemish, or damage the case or components. On a separate page, we provide extensive instructions for cleaning AirPods.
Step 8: Only use one AirPod
- According to reports, the problem occurs less frequently if you only use one earbud, so you may leave one in the charging case.
- You could also configure your AirPods so that only one AirPod microphone is used.
- Go to Settings > Bluetooth on your iOS device and choose AirPods when the AirPods case is open.
Tap the I and then choose Microphone from the menu.
The default setting is Automatic, and both AirPods include a microphone. You can, however, set this to Always Left or Always Right.
Step 9: Disable Automatic Ear Detection
- This is another function you should experiment with to see whether it improves the performance of your AirPods.
- On your iOS device, go to Settings > Bluetooth.
- Turn off Automatic Ear Detection by tapping the I next to your AirPods.
- This function should instantly redirect audio to your AirPods as soon as it detects they’re in your ears, but it’s worth double-checking to see if something isn’t working properly.
Step 10: Disconnect your Watch
The problem could be due to connecting with both an Apple Watch and AirPods, so unpair your Watch and see if the problem persists.
If you have other Bluetooth devices, it’s a good idea to unpair them as well, just in case something is causing a problem.
Step 11: Disable Wi-Fi on your iPhone
We’re not sure why this would make a difference, but some customers have reported that turning off Wi-Fi on their iPhones solved the audio-related problem. This could be due to sources of WiFi interference, which we shall investigate in the next stage.
Step 12: Look for Wi-Fi or Bluetooth interference sources
There are numerous gadgets that could be creating interference, so it’s conceivable that one of them is causing your audio drops. Here are some measures you can take to avoid it. If the problem occurs while you are on a call, move closer to your Bluetooth device, such as your iPhone.
Microwave ovens, fluorescent lights, wireless video cameras (such as baby monitors), and cordless phones should all be avoided. To free up the 2.5GHz frequency for Bluetooth, move devices that can use it to the 5GHz range. (Learn how to switch to the 5GHz spectrum here).
READ ALSO: How To Fix Unbalanced Headphones? (6 Easy Ways!)
How to Restore Disconnected AirPods from a Mac?
- Check your Sound settings in System Preferences on your Mac if the problem is due to utilizing the AirPods with your Mac.
- Select your AirPods under the Output tab in System Preferences > Sound.
- Repeat the process under the Input tab.
If the problem occurs during FaceTime or audio calls conducted on your Mac, with callers claiming that your voice isn’t clear or that they can’t hear you, it could be due to Bluetooth having to send and receive audio. As a result, the sound quality may shift from high to poor fidelity.
Separately, we have information on which devices work with AirPods.
CONCLUSION On Why do Headphones Keep Disconnecting
Even if your Bluetooth keeps disconnecting, it is a fantastic piece of technology. Wireless Bluetooth headsets will only grow in popularity as time goes on, thus this is a technology worth investing in. After all, Bluetooth permanently eliminates the issue of tangled headphones and tangled connections.
Although you may encounter difficulties connecting your Bluetooth item to your phone, they are easily overcome. You should first attempt to determine the precise problem with your Bluetooth headset before attempting to repair it.
Consider the issues mentioned. Do you have many wireless routers in your home? Do you have a habit of leaving programs running in the background? Or, perhaps, you haven’t updated your firmware in a long time.
Once you’ve determined why your Bluetooth keeps disconnecting, you can implement appropriate corrective solutions for the issue at hand. Whether it’s as simple as restarting your device or as time-consuming as eliminating duplicate contacts, your Bluetooth device will soon be operational.
FAQs About Headphones Keep Disconnecting
What can I do to keep my headphones from disconnecting?
Check that your phone is not in airplane mode. Attempt to restart both devices. Avoid interference by moving away from any device that could disturb your signal. Ascertain that your smartphone and headphones are within an acceptable range of each other for connection.
Why do my iPhone headphones constantly disconnect?
The issue could be related to the sensors within the AirPods that determine whether or not they’re in your ears, or it could be due to Bluetooth interference.
What’s the deal with the orange blinking AirPods?
Amber, your AirPods or AirPods Pro are not completely charged. If your AirPods or AirPods Pro are flashing amber, there is a problem. You must first factory reset them before re-pairing them with your device. Anyone encountering connectivity troubles with their AirPods or AirPods Pro should factory reset them.
When it comes to our homes, one of the most important things is the safety and security of our belongings. Whether you own your home or you're renting, personal property insurance can provide you...
There's no denying that renting a place comes with its advantages - no mortgage, no property taxes, and flexibility to move around when needed. However, one aspect that often gets overlooked is the...