Jaybird headphones are popular among both athletes and non-athletes.
If you bought your Jaybird headphone secondhand or simply forgot how to connect them, the two techniques below will work for almost all models.
You may have just purchased a new pair of headphones, or you may be researching how to solve Bluetooth latency. In any case, we are here to assist you in connecting your Jaybirds!
Read the whole article for full details.
Quick Answer, How to Connect Jaybird Headphones?
Press and hold the Power Button while your headphones are turned off until you see the LED blinking red/green. The headphones are ready to pair when the LED flashes red/green. “Searching for your music device,” a voice prompt will say. To connect, select “Jaybird FREEDOM” from the list of found devices.
How to Connect Jaybird Run Earphones?
Your Jaybird RUN earphones are ready to pair right out of the box.
- Take your earphones out of the charging case and insert them into your ears.
- Go to Bluetooth settings on your Bluetooth device, make sure Bluetooth is turned on, and choose Jaybird RUN from the list of accessible devices.
- You will hear “Connected” on your right earphone after you are connected. The right earbud is the master and will immediately link to the left earpiece.
Other Steps to Follow on How to Connect Jaybird Headphones
Install the Jaybird App
There are two ways to connect your Jaybird headphones to your phone, computer, or other devices. To begin, download the Jaybird App. You may use this to connect to your bluetooth headphones and control things like volume limits and EQ.
If you don’t have a phone, you can link your Jaybird headphones or wireless headphones to any device by turning them off, then turning them back on while holding down the power button for 3-4 seconds.
After this time, your Jaybird headphones’ LED indicator light will begin to flash red and green, signaling that it is ready to pair.
Follow the procedures below to link an additional Bluetooth device or to manually activate pairing mode
- Begin with the earbuds in the charging case:
- Begin by placing both earphones in the charging case and closing the lid.
- Remove your right bluetooth earbud from the charging case by opening the charging case.
- Close the charging case and turn off your right true wireless earbud for 3 seconds by pushing the multifunction button.
- Hold down the right multifunction button for 6 seconds, or until the LED flashes green. The earbud is in pairing mode when the LED flashes green.
- “Go to Bluetooth settings and pick Jaybird RUN,” a voice prompt will say.
- Go to your device’s Bluetooth settings and choose “Jaybird RUN” from the list of found devices to connect.
- You will hear “Connected” from your right earpiece after you are connected. The right earbud is the master and will automatically peer connect to the left earpiece.
Connecting your Jaybird Earbuds to a Mmobile Device
1. Turn on Bluetooth® on your phone/music device and make sure it is actively searching for Bluetooth devices.
2. Turn off your Tarah earbuds and push and hold the Middle Button until the LED flashes white. You will hear the phrase “READY TO PAIR?” DOWNLOAD THE JAYBIRD APP FOR HELPED SETUP” audio prompt.
3. From the list of found devices, select “Jaybird Tarah.”
4. After connecting your Tarah earphones to your phone/music device, you will hear the “Connected” voice prompt. You are now prepared to listen to music.
How to Connect Jaybird Freedom buds to phone or music player?
Your FREEDOM headphones are ready to pair right out of the box. Here’s how it works:
- Put on your FREEDOM headphones.
- Find Jaybird FREEDOM in the list of available devices on your Bluetooth music device. Some gadgets may require you to scan for accessible Bluetooth devices.
- To connect, select Jaybird FREEDOM from the list. When you are connected, you will hear the phrase “Headphones connected” from your headphones.
If you want to connect your FREEDOM headphones to another Bluetooth device, you must first enter pairing mode:
- Press and hold the Power Button while your headphones are turned off until you see the LED blinking red/green. The headphones are ready to pair when the LED flashes red/green.
- “Searching for your music device,” a voice prompt will say.
- To connect, select “Jaybird FREEDOM” from the list of found devices. When you are connected, you will hear the phrase “Headphones connected” from your headphones.
How to connect Jaybird Tarah to Phone?
- Turn on Bluetooth on your phone/music device and make sure it is actively searching for Bluetooth devices
- Turn off your Tarah earbuds and push and hold the Middle Button until the LED flashes white. You will hear the phrase “READY TO PAIR?” DOWNLOAD THE JAYBIRD APP FOR HELPED SETUP” audio prompt.
- In the list of found devices, select “Jaybird Tarah.”
- You will hear the “Linked” voice prompt once your Tarah earphones have connected to your phone/music device. You are now prepared to listen to music.
If the pairing fails, turn off your earbuds by pressing the Middle Button until the red LED glows and a decreasing “Power off” tone is heard. Steps A-D should be repeated once your earbuds have been turned off.
NOTE: When you initially turn on your Tarah earphones or after a reset, they will be in pairing mode.
Why can’t I pair Earbuds with Another Bluetooth Device?
Your X3 buds are ready to pair right out of the box and can remember the pairing information for up to 8 devices.
If you want to link your buds with another audio source device, you must first manually activate pairing mode on your buds:
With your buds turned off, push and hold the Power Button until the LED begins to glow red/green. The buds are ready to couple when the LED flashes red/green.
“Searching for your music device,” a voice prompt will say.
To connect, select “Jaybird X3” from the list of found devices. When your buds are connected, you will hear “Headphones connected.”
Final Thoughts on How to Connect Jaybird Headphones
Connecting your Jaybird Headphones is as easy as other headphones brands including jbl, beats powerbeats, bose, galaxy buds, apple airpods, quietcomfort earbuds. Just make sure that the battery is good and has wireless charging.
We hope that the article is useful for you to know how to connect jaybird headphones!
Frequently Asked Questions (FAQS)
What is the best way to connect my Jaybird headphones to my iPhone?
Hold the Middle Button on your X4 earphones until the LED blinks green/red and you hear the “Ready to pair.”
Go to the Bluetooth settings menu on your Bluetooth music player and look for ‘Jaybird X4’ in the list of possible devices.
To connect, select ‘Jaybird X4’ from the list.
What is the procedure for resetting my Jaybird X2 headphones?
When you restart your X2, the headset will enter pairing mode (green and red alternating lights). When in pairing mode, hold down both volume buttons for 3 seconds. The X2 light will flash yellow three times to signify that the headset has been reset. Your headphones have been re-set.
Why do my Jaybirds continually telling me that my headphones are connected?
If you hear “Connected” from your Tarah earbuds repeatedly, they may be connecting to another associated device. Turn off Bluetooth® on any other paired device to try to isolate this.
The Phillips SHP9500 is an excellent pair of critical listening open back headphone on a budget. You can find these headphones in many stores, markets, and even online!...
Hear us out! No one likes extra cables or dongles because they can cause problems, but these are necessary if you want to use your expensive headphones with the latest...